CLEANING WOOD FLOORS
Abrasive particles like dirt, sand or gravel gather on the surface of your hardwood floors, making them look dull and causing scratches. Mats, runners or area rugs placed near entryways help catch dirt where it enters. In fact, doormats can eliminate 80 percent of the dirt tracked inside a home.
To start, clean up food and water spills immediately. Then make sure to mop and vacuum frequently. Mop the floor with a cleaner especially made for the type of hardwood floors that you have installed. If you are looking for a chemical-free approach, invest in a steam cleaner. Or kick it up a notch with a combination vacuum/steam mop.
To protect the finish, never use silicone-based polish, cleaners that contain oil, wax or ammonia, or vinegar solutions to clean your floor. Vinegar contains acid that will dull out floors over time.
REMOVE STAINS FROM WOOD FLOORS
Water spots – Water can cause white spots to form on a wood floor’s finish. Apply a small amount of mineral spirits to an extra-fine steel wool pad and rub the spotted area in a circular motion.
Food stains – Wipe the area with a damp cloth, then rub dry and wax.
Place glides or pads on the bottom of furniture legs to prevent scratches, dents and other forms of damage on the floor finish. To keep wood floors looking their best, put down rugs and runners in high-traffic areas. Take extra care when moving heavy objects to avoid scuffing.
For an inexpensive, easy solution, slide socks onto chair and table legs so that they don’t scratch the floor when moving furniture around. If you have pets, trim their nails or claws regularly so they don’t damage the floor over time.
Use a soft-haired broom when sweeping floors to prevent scratching. If vacuuming, make sure to turn on the setting intended for flooring.
RUB OUT SCUFF MARKS – Use a little water and rub the scuffed area. For stubborn marks, you can spray a cloth with hardwood floor cleaner and lightly rub clean. Or gently rub the scuff with an extra-fine steel wool pad.
REMOVE HEEL DENTS AND OTHER GOUGES – A beautiful stiletto heel can turn heads, but destroy your hardwood floors. To fix the pockmarks that pointy heels create, as well as gouges left by furniture, you may need to sand the floor down to the raw wood and refinish it.
REPAIR SCRATCHES – If your floor is the victim of scratches that don’t penetrate all the way through the wood, you can repair it in a few hours. Use a buffer to scuff-sand floors and apply a coat or two of wood finish. This process is easier and less expensive than sanding and refinishing. You can rent a buffer from your local home center. After buffing and roughing up the surface, apply a polyurethane stain. Follow directions for re-coat time. Generally, water-based stains need to be re-coated in 3 hours and oil-based in 8 or more hours.
Grab a marker – Hide surface scratches by touching them up with a stain-filled marker.
Rub the scratch with the edge of a quarter – If this doesn’t conceal the scratch enough, rub a small amount of paste wax and buff it with a soft cloth.
Walnuts are more than just a snack – Repair shallow scratches by rubbing shelled nuts on the surface. The natural oils in nuts help conceal the flaws.
Spot sand it – Use extra-fine sandpaper or steel wool to gently buff scratched or chipped areas, then use a cotton swab or small paintbrush to re-stain wood.
REVIVE DULL FLOORS
For floors that are lackluster or contain mere surface scratches, you can actually skip the sanding and simply re-coat the wood. Refinishing kits, such as Varathane No-Sanding Floor Refinishing Kit, contain supplies to condition and refinish floors. Remember these kits are best for minor scuffs and scratches in the floor’s finish, not the wood itself. Extensive blemishes and deep-penetrating scratches will need to be sanded and refinished.
SILENCE SQUEAKY FLOORS
Squeaky floors make it hard for someone to sneak up behind you, but the benefits end there. To silence squeaks, turn your attention to the sub-floor, which acts as backing to hold the flooring in place. Secure the sub-floor to wood flooring from below by driving screws at a slight angle. Use screws short enough not to break the surface of the face of the wood.
Another easy solution is a Counter-Snap Kit that utilizes a screwdriver bit, depth-control fixture and breakaway screws. When drilling, the screw-head automatically breaks off when you drive the screw to a certain depth. This will leave you with non-squeaky floors and undetectable screws.
Also, you can try sprinkling talcum powder, baking soda or candle wax on floorboards to help quiet squeaky floors.
FIX GAPS BETWEEN FLOORBOARDS
Wood naturally expands. Gaps in between hardwood floor boards often occur due to the moisture levels in the wood and the air temperature in your home. Dry winter air and heating sucks out moisture, causing boards to shrink and gaps to form in the floor. Fix this problem by using a humidifier to control the air inside your home. In the spring and summer, higher humidity levels will cause the wood to expand, closing the gaps.
Generally temperatures between 60 degrees and 80 degrees and a humidity level in the range of 35 to 55 percent is optimal for wood floors. These levels will help retain the proper moisture in the floor’s wood fibers.
Another option for repair is to apply wood filler in the gaps. However, when the floor contracts and expands, the filler can easily pop out or fall into the gap. Thus wood filler is only a temporary fix and not an ideal option. If you find that a humidifier is not minimizing the gaps, it’s best to call a professional for a lasting repair.